How to fix a paintball gun that won’t shoot – Easy Fix

How to fix a paintball gun that won't shoot

Unable to shoot is pretty frustrating for any paintballer. It can be tough to pin down exactly what the problem is. The best way to solve issues with your paintball gun is to identify the cause of the problem yourself. You don’t want to ship your marker off only to see it come back without full resolution of your issue or, worse, an expensive repair bill. Paintball gun repair isn’t easy at all.

You might not want to do it yourself if the gun is high-end or if there are problems you don’t understand. With the right diagnostic skills and paintball repair kit, you can usually figure it out with minimal trouble. But, when you’ve got a low-end paintball gun that has enough sentimental value that you don’t want to replace it, here’s how to fix a paintball gun that won’t shoot.

Why isn’t my paintball gun shooting?

A paintball gun not shooting is often an easy fix if you identify it. Below are some causes of a paintball gun not shooting,

  • Dirty barrel
  • Clogged barrel
  • False trigger pull or lousy trigger pull
  • Blowback issues
  • Obstructed hammer
  • Weak or missing o-rings
  • Dry paintball gun
  • Shootdown or cutdown bolt
Paintball gun repair

How to fix paintball gun that won’t shoot: Step by Step guide

There are many reasons why your paintball gun might not be working. This article will help you troubleshoot common paintball gun problems and find solutions. How to shoot a paintball gun fast? Follow the tips below to get your paintball gun up and run.

1. Check Your Tank’s Air Pressure

Air from the compressed air tank of CO2 enters the regulator, converting it into liquid CO2. After that, it’s transferred to a solenoid valve, which allows air to flow into the gun when you pull the trigger. Make sure your tank still has gas inside. If there is no air in the tank, nothing will come out of the barrel. Also, check that the o-ring is in place and not damaged before you try firing again. If your marker is still not firing, proceed to step number 2.

2. Check Your Regulator

The regulator is vital for the proper operation of your paintball marker (gun). If there is a problem, you won’t be able to use your marker until it’s fixed or replaced with a new one. It regulates pressure so that CO2 can flow through at a constant rate when you pull the trigger. You should screw the regulator into the tank tightly in that case.

3. Examine the hopper

Worrying how to fix a jammed paintball gun? Sometimes a jam in the hopper can cause your marker not to fire properly (or at all). If this is the case, open up the hopper and take out any ball that may be stuck inside. The sensor of your marker will think that there’s already a ball in place, so it won’t fire another one until you remove the old one.

4. Check the Barrel

Ensure that there’s no debris or other obstructions in your barrel that would prevent a paintball from passing through it. It can happen from time to time if you don’t clean your barrel correctly after a long day of play. By cleaning your gun properly, you will never face the problem of a paintball gun leaking air from the barrel.

5. Check for Leaks

Are you owning paintball guns and have any of these questions: “How to fix paintball gun air leak?” or “How to fix paintball gun air?” Use a leak detection solution or soap water to check for air leaks in your marker. If you find one, use an appropriate sealant to plug it up and make sure it’s sealed tight so no more air can escape from inside the tank.

5. Check for broken parts in your hopper/loader or your gun.

As strange as this may sound, many times, a piece of a broken paintball will get lodged in your hopper or loader, jamming it up and making it unable for any more balls to enter or exit the chamber. The same goes for any broken parts on your marker. If you have a crack on the part of it, sometimes a piece of that can get lodged within the interior workings.

6. Clean and lubricate your paintball gun

Take the barrel out and soak it in a bucket of water for a few minutes. Also, take the bolt out of your gun (if you have an aftermarket bolt) or push it back as far as possible. Soak the whole gun in a bucket of water. It will help you remove any paint or dirt from inside the gun. Drain all the water from the gun and barrel and remove any remaining dirt with a rag & lubricant.

How to service your paintball gun?

To keep the gun shooting correctly, you must clean and lubricate it regularly.

  1. Clean the barrel after each game. Scrub it with a barrel swab soaked in water, then dry it with a towel.
  2. Remove the CO2 tank from the gun and let the air chamber deflate before storing the gun. Never store a paintball gun with a CO2 Reg still in place.
  3. Dismantle your paintball gun and wipe all components down with a cloth soaked in water to remove any paint or dirt particles. Dry all parts thoroughly with a clean cloth to prevent rust or corrosion.
  4. Apply a light coat of oil to all moving parts of the marker, avoiding getting oil in any of the air passages or other small openings. Also, apply oil to the barrel and any screws or other threaded fittings on the gun.

Where to get paintball gun repaired?

There are a handful of places for a paintball gun repair, including:

Paintball Shop

It is probably the best place to go if you’re having an issue with your gun. If a paintball shop doesn’t have the parts you need in stock, it can order them and install them for you. It’s also likely that they’ll have experienced hands-on staff who should be able to fix the problem (or at least diagnose it) reasonably quickly. The downside of this option is that it can be more expensive than doing it yourself or sending it back to the manufacturer for repair.

Paintball Forums

Some paintball forums allow people to post their questions about problems they’re having with their equipment. It can be an excellent place to get help from other players and hobbyists, but keep in mind that you’re getting advice from non-experts. So take everything with a grain of salt and don’t attempt any repairs unless you know what you’re doing.

Manufacturer Website

Most manufacturers will have information on their websites about how to contact them for repairs or warranty claims and instructions on how to send your item back if necessary. The advantage of sending your gun back is that they may be able to fix any problems. It is a great idea to contact the manufacturer for paintball gun repair. 

How to fix a leaking paintball gun?

Wrap the air tank with a towel and hold your gun upside down. Hold the trigger down and shoot the gun with your hand until no paint comes out. Now you want to add some oil to your paintball gun. If you have some dow 33 or oil for guns, use that. If not, you can use vegetable oil or whatever oil you have. Do not use wd-40 as it will clog up other parts of your gun. You only need a small amount of oil. Put the oil in through the airflow hole and get it on all of the o rings.

Why is my paintball gun rapid-firing?

There are many reasons why a paintball gun may start to rapid-fire (fire more than once with each trigger pulled). Most of these problems are easy to fix and only require a few tools. These are most common reasons why paintball gun is not consistent in shooting velocity are:

  • Worn out sear or trigger components.
  • Dirty or damaged O-rings in the bolt system.
  • Improperly lubricated O-rings in the bolt system.
  • Air Leaks in the air system.
  • Dirty or damaged connectors, hoses, and tank threads.

Final Words

Sometimes, you have to shoot in games. But if your paintball gun would not fire, you are going to be out of luck. However, the greatest tool you can have in diagnosing the problem with your beloved marker is knowledge. You’ll use that tool right here as we list techniques you can use when trying to diagnose a problem with your paintball gun. Hopefully, this post on “How to fix a paintball gun that won’t shoot” will help you revive and restore the fire and power to your buddy.

Also Read: Best paintball gloves

Similar Posts